Xilo Stax Combo F4 Flight Controller & 4-in-1 45A ESC - 2pc Stack

Xilo Stax Combo F4 Flight Controller & 4-in-1 45A ESC - 2pc Stack

by Xilo

Sold out

$74.99

SKU

Quantity

Manufacturer Description

Stax F4 Flight Controller Version 1.1 update!

Spacing for receiver pins (XM+ and Crossfire Nano) is now correct!
16MB onboard flash for Blackbox

The Stax Combo continues XILO's tradition of giving you high-quality FPV gear for a low price point. And it couldn't be easier to install and use on your favorite airframe!

Remove the mess of soldering and the chance of making a mistake during build time. The Stax plug n' play capability allows you to simply connect the FC and ESC with the included 8pin harness, simply wire up your motors and accessories, and you are good to go!

The F4 flight controller gives you proven rock solid processing power while the ICM20602 Gyro / Accelerometer (up to 32KHz) gives accurate gyro information while in use. The 4-in-1 ESC uses F3 processing power to allow complex power management without a hitch. The ESC supports up to 6s input voltage while 45 amps continuous support gives you plenty of headroom to push your mini quads to the limit.

The XILO Stax FC has the unique ability to mount XM+ and Crossfire Nano style receivers directly to the FC. This saves space and makes for an overall cleaner build. If you are using a "slammed" style frame, this feature is very handy as the receiver won't add any additional height to your stack.

Another key feature on the Stax FC is the remote VTX power switch. With the XILO Stax flight controller, you can map a switch on your radio to turn on or off your VTX. This is useful when you are plugging in and don't want to broadcast video signal or you crashed your quad and want to prevent a roasted VTX. When a video transmitter isn't in flight it can quickly overheat due to lack of air flow, and this ability to control power can save you many burnt up VTXs.

The Stax uses standard 30.5mm / 30.5mm mounting hole configuration and the FC and ESC include M3 silicone mounting grommets to reduce vibrations to your gyro, ensuring accurate readings.

Other features such as OSD, telemetry, multiple UARTs, 5V pads, SBUS and PPM support, all come standard with the XILO Stax.

Whether you are looking for a stack for a brand new build or just to freshen up an older quad, the XILO Stax will get the job done, without breaking the bank.

Features

F4 Flight Controller

2s - 6s Direct Lipo input support (5-26v)
On-board BetaFlight OSD
VTX Remote Power switch
On-board 5V / 2A and 3.3V / 0.2A regulators
SBUS and PPM support
RGB LED dedicated pad
VBAT Monitoring support
16MB Flash for Blackbox
6x UART Ports
Betaflight support (Supports DSHOT protocol)
BLHeli pass-through flashing supported by hardware

4-in-1 ESC

4x F3 processers
Latest Gen. firmware using BLHeli-32
3s - 6s LiPo battery compatible
45A per channel, 55A burst
Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us), with Auto-detection
Lightweight, and compact size
Adaptive timing, compatible with a wide range of motors and KV
Synchronous rectification technology adds efficiency, damped light
Powerful regenerative braking / active braking.

Specifications

F4 Flight Controller

STM32F405 (2MB flash) 32-bit processor
ICM20602 Gyro / Accelerometer (Up to 32KHz)
High quality 1.6mm PCB
Micro USB connector for programming
Mounting Holes: 30.5mm (square to center of holes)
Dimensions: 36mm / 36mm / 6mm (includes USB in height)
Weight: 7g

4-in-1 ESC

Input: 3s - 6s LiPo
Constant: 45 Amps (per channel)
Burst: 55 Amps (per channel)
BEC: No
Mounting Holes: 30.5mm (square to center of holes)
Dimensions: 36mm / 43mm (including power pads)
Weight: 12g (without motor wires)

Components

1x Stax Combo F4 FC & 45A ESC Stack

F4 Flight Controller
45A BLHeli-32 4-in-1 ESC

2x 8pin Harness
1x 8pin Extended Harness
12x Silicone Grommets
2x 35v 470uf Capacitor
1x XT60 Connector
2x 14 AWG wire

How to Setup Remote VTX Power Switch

The XILO Stax flight controller features a power pad for your video transmitter that can be remotely controlled via a switch setup in Betaflight. This allows you to remotely turn your VTX on or off from your radio! Simply solder your VTX to the corresponding pads on the Stax FC (VTX, S/A, PWR, GND) and the PWR pad will provide your VTX with filtered VBATT power. By default, the pad will be powered on. Go into Beta to set up a switch if you want to control power on/off remotely. You will find it under the "Modes" tab and "USER1" switch. Assign this to the AUX switch of your choice to turn the power on/off for that PWR pad. Easy!

Free Shipping

Xilo

Xilo Stax Combo F4 Flight Controller & 4-in-1 45A ESC - 2pc Stack

Xilo

You recently viewed

Store Info

Product Catalog

Subscribe

Follow us